DIY Guide: How to Replace your Bathroom Faucet

Whether or not your toilet is outdated or cheesy, otherwise you’re simply within the temper for one thing new and totally different, updating your toilet sink fixture is a fairly straightforward DIY undertaking. In a couple of brief hours, you possibly can have a shiny, new, and clear faucet. You possibly can even set up cool tech in your bathroom, like lights or a touchless faucet (which can assist you keep away from these nasty flu germs). So long as you realize what you’re doing, installing a sink fixture is fairly painless.

Earlier than you get out your plumber’s belt, take a look at our information on learn how to change a toilet faucet. We’ll assist you to get by the method from begin to end with out getting water in every single place.

Stuff you’ll want:

Step 1: Look at your outdated faucet and sink. Notice the kind of faucet you at present have, the connections, and the house out there above and below your sink.

Step 2: Select a brand new faucet that meets the suitable dimension and specs in your sink. Most sinks will match both a middle set, single gap, or widespread faucet. Some taps are even wall-mounted. Ensure you know what sort of faucet to buy, so you possibly can set up it correctly. If in case you have a pedestal sink, you’ll have house limitations below the sink to contemplate as effectively.

Step 3: Take away every part from below your sink, so you may have a clear and decluttered working space. Get a bucket and a few rags prepared as a result of you’ll need them shortly.

Step 4: Flip off each of your water strains. Flip every knob clockwise to show it off. Flip in your faucet to empty out leftover water.

Step 4:  Disconnect the outdated faucet.

Step 4a: Disconnect the p-trap. The p-trap is the j-shaped pipe below your sink that connects to the drain. Earlier than you begin eradicating something, put a bucket beneath to catch any water that escapes. It’s regular for water to fall out once you disconnect the p-trap. After getting your bucket and rags prepared, flip the 2 nuts on every finish of the p-trap counterclockwise to take away them. If the nuts are too tight to disconnect by hand, use a wrench to assist loosen them.

Step 4b: Disconnect the water provide line connections out of your outdated faucet. On the underside of your faucet, you’ll see your outdated faucet’s nuts and water provide line connections. The water provide line connections needs to be positioned under the tap nuts.

A basin wrench is the very best software for this, however in a pinch, one other adjustable wrench you may have out there can do the job. Use your wrench to loosen the water provide connections from beneath your faucet. After you loosen the water provide line connections with a wrench (you’ll possible have to show them clockwise), take away the road the rest of the way in which along with your hand. Be certain to catch any water that escapes when eradicating the water line.

Step 4c: Unscrew the nuts from below your faucet. The tap nuts are positioned above the water provide line connections, and these nuts are what holds your faucet in place. It’s possible you’ll want to make use of a wrench and a few WD-40 if you happen to can’t take away them by hand.

Step 5: Take out the drain. You’ll see a bar with holes in it operating behind the sink and pipes. That is the clevis strap. On the clevis strap, you’ll see a bit of clip referred to as the spring clip. Take away this  and pull the strap by the rod so you possibly can flip the drain pipe freely.

Unscrew the drain pipe and take away it. Use a wrench to loosen it if you possibly can’t take away it by hand. After that, unscrew and take away the highest of the drain (the flange) from inside your sink.

Step 6: Take away the remaining elements and clear the realm. It is best to have the ability to merely pull out your outdated faucet. Take away any outdated silicone caulk or plumber’s putty utilizing a knife, scour pad, or sponge. You need your sink to look as very similar to a model new sink as doable.

Step 7: Set up your new faucet. Every producer could have barely totally different set up directions. Nevertheless, most taps observe comparable set up steps.

Step 7a: Place the gasket on the underside of the tap, put the tap into the mounting holes in your sink, after which tighten the nuts to safe the tap in place. Relying on the kind of faucet you buy, you might also have to put in your faucet’s handles. Comply with the producer’s directions to put in the tap handles.

Step 7b: Set up the brand new drain. The drain generally comes partially assembled. You might even see gaskets linked to the flange, or a drain nut screwed onto the flange. Take away the drain nut from the flange. Apply a small quantity of silicone or plumber’s putty below the flange, after which place it in place inside your sink. Beneath the sink, placed on the gaskets and screw the nut onto the flange. Use a wrench to tighten it, as you don’t need your sink to leak.

After your flange and nut are in place, screw on the drain pipe. The drain pipe has one other gap on the aspect of it (the pivot nut) the place the drain rod connects. Be certain this gap is dealing with the again, or away from you.

Set up the drain rod. Unscrew the pivot nut, place the drain rod inside the outlet, after which tighten the nut. Slide on the clevis strap (the bar with holes in it) and spring clip.

Again up on the high of your sink, insert the down rod in your drain stopper (the factor that opens and closes your drain so you possibly can fill it up with water) by the outlet in your faucet. Information it down by to the clevis strap, and safe the rod to the clevis strap with the screw.

Step 7c: Join the provision strains. Your new faucet could include new water provide strains. In case you are changing the outdated provide strains, you’ll have to disconnect them on the shutoff factors. Then, set up the brand new provide strains. Join one finish to the recent water shutoff valve, then join the opposite finish to the recent water provide line connection. Do the identical for the chilly water. Tighten your water provide strains, however don’t over-tighten the connections.

Step 7d: Join the p-trap. Join each nuts in your p-trap. You wish to have the p-trap pipe barely overlap the vertical pipe (by an inch or so). It’s also possible to buy p-trap extenders for added safety.

Step 8: Take a look at your new faucet. Activate the water, and let cold and hot run for a couple of minutes. Verify for any leaks, and tighten any connections if it’s worthwhile to. As soon as every part is operating easily, you possibly can get pleasure from your new faucet.

Concerns:

• Some folks select to not change sure elements like water provide strains. In case your new faucet comes with these elements, and they’re suitable with your house, it’s a good suggestion to exchange your outdated elements with new ones.
• Some faucet producers present instruments that may assist set up your new faucet. These instruments generally is a useful timesaver, so it’s greatest to reap the benefits of them.
• In case you are going from a three-hole to a single-hole faucet, be sure to measure the gap throughout the holes and get an acceptable plate to cowl them.

WWW.WOWOWFAUCET.COM